You want to identify the left baffle and the right baffle first, by placing the baffle along side the frame to fit the shape. Step 3: Now you can tighten all (4) 8mm bolts so the T-Slot nuts lock the board into the frame. Step 3: Slide the board horizontally to leave about 30mm of space between the board and the left edge of the machine as shown below.
#Sainsmart oscilloscope assembly install#
Install the board by inserting (4) M3 20mm T-Slot nuts onto the top and bottom beams on the frame, like shown in the figure below. Step 2: Position the frame so that the back of the machine is facing you. Keep the nut loose and in horizontal position so that they can be inserted into the beams in step 2. Put on the M3 T-Slot nuts trough the holes into M4 8mm bolts. Step 1: Locate the four pre-drilled holes in the corners on the control board. Remove protection paper tape from acrylic pieces on the main board. The main board goes to the back of the machine (the opposite side of the spindle). Now let's move onto wiring! Part 3 - Wiring 3.1 Install the Main Control Board Do not over tighten the screw, as it can damage the mount.Ĭongratulations! Now your machine frame is fully assembled! Step 4: Tighten the Hex screw to secure the Spindle. Step 3: Slide the spindle into the mount until the external sleeve of the spindle is fully inserted. Step 2: Loosen the Spindle Mount Hex Screw Then screw the the collet collar back to the spindle. Make sure the collet is locked in place by pushing it. Step 1: Unscrew the black collet collar from the spindle and insert the collet. Step 4: Repeat the process on the opposite side. Keep the screws loose until you finish the other side. Step 3: Install (6) M5 14mm screws into the T-Slot nuts. See through the six pre-drilled holes on the side of the gantry to make sure they align with the nuts positioned in 2.5. Step 2: Place the Acrylic Spacer template underneath the gantry to prop a side up at a time. Step 1: Set the X-Axis / Z Axis Gantry over your Y-Axis Base Assembly as shown below. 2.6 Install Y-Axis Base to X / Z Axis Gantry There should be a 31.5mm clearance(the longest space on the spacer) between the back T-Slot nuts and Rear of the machine as shown in the following picture. Step 3: Insert the Acrylic Spacer Template into the slot and space out the T-slot nuts as shown below. Position near the back of the machine (Stepper Motor Side). Step 2: Insert (6) Tension T-Slot Nuts on each side. Step 1: Position the Y-Axis base assembly so that the step motor is facing your right hand side. You don't need a spacer for this limit switch. Step 3: Now install the remaining Limit switch on the opposite side, using the 5mm M3 screws. Two on the inside and two on the outside. Step 2: Install four cable holders on the same side of the gantry. Using (2) M3 20mm screws to secure the limit switch followed by the spacers into the frame. Locate the two pre-drilled holes on the inside of the gantry next to the lead screw, as shown in the picture below. You will need the two white ABS spacers and the longer 20mm M3 screws for this step. Step 1: The first limit switch to install is on the stepper motor side. Step 1: Locate the 4 pre-drilled holes and install the rubber feet on each corner using the Allen wrench 2.4 Installing Limit Switches to X-Axis/Z-Axis Gantry 2.3 Installing Rubber feet to Y-Axis Base Assembly Step 3: Install the limit switch by tightening the 3mm screws. Install two on the outside of the frame in the back (the stepper motor side) Install two cable holders on each side, facing inside the frame.
Step 2: Install cable wire holders in the pre-drilled holes next to the limit switches, using the 3mm screws. Step 1: Locate the Limit switch mount indents on the inner side of the frame. 2.2 Installing limit switches & cable holders to Y-Axis Step 3: Tighten (2) M6 16mm screws to secure the lead screw mount. Step 2: Align the Aluminum Build Plate center slot with the blue Y-Axis lead screw mount as shown in the picture. Step 1: Flip the Y-Axis Base Assembly upside down and remove the cable ties from the bearing mount In addition to this guide, you can watch this video and this video to see the actual assembly process.
#Sainsmart oscilloscope assembly drivers#
Installing drivers and starting your first project.3.6 Connecting the Stepper Motor cables.2.6 Install Y-Axis Base to X / Z Axis Gantry.2.4 Installing Limit Switches to X-Axis/Z-Axis Gantry.2.3 Installing Rubber feet to Y-Axis Base Assembly.2.2 Installing limit switches & cable holders to Y-Axis.
0 kommentar(er)
